Error: command ['sh', '-c', 'dmesg | comm -13 /var/log/dmesg -'] failed with exit code 1: [   91.778134] e1000e 0000:01:00.0: irq 27 for MSI/MSI-X
[   91.832449] e1000e 0000:01:00.0: irq 27 for MSI/MSI-X
[   91.835020] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   91.839758] iwl3945 0000:02:00.0: firmware: requesting iwlwifi-3945-2.ucode
[   91.931647] iwl3945 0000:02:00.0: loaded firmware version 15.32.2.9
[   92.052772] Registered led device: iwl-phy0::radio
[   92.053165] Registered led device: iwl-phy0::assoc
[   92.054119] Registered led device: iwl-phy0::RX
[   92.054377] Registered led device: iwl-phy0::TX
[   92.079116] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   96.753077] i2c-adapter i2c-1: unable to read EDID block.
[   96.753083] i915 0000:00:02.0: LVDS-1: no EDID data
[   96.896242] i2c-adapter i2c-1: unable to read EDID block.
[   96.896246] i915 0000:00:02.0: LVDS-1: no EDID data
[   97.092071] i2c-adapter i2c-1: unable to read EDID block.
[   97.092077] i915 0000:00:02.0: LVDS-1: no EDID data
comm: file 2 is not in sorted order
[  102.515073] wlan0: authenticate with AP 00:60:b3:75:73:e9
[  102.516610] wlan0: authenticated
[  102.516613] wlan0: associate with AP 00:60:b3:75:73:e9
[  102.518795] wlan0: RX AssocResp from 00:60:b3:75:73:e9 (capab=0x1 status=0 aid=25)
[  102.518799] wlan0: associated
[  102.521773] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  112.720065] wlan0: no IPv6 routers present
[  115.950024] CIFS: Unknown mount option codepage
[  115.950046] CIFS: Unknown mount option unicode
[  133.765180] CE: hpet increasing min_delta_ns to 15000 nsec
[  243.746789] padlock: VIA PadLock not detected.
[  249.360088] i2c-adapter i2c-1: unable to read EDID block.
[  249.360096] i915 0000:00:02.0: LVDS-1: no EDID data
[  249.505077] i2c-adapter i2c-1: unable to read EDID block.
[  249.505085] i915 0000:00:02.0: LVDS-1: no EDID data
[  249.649065] i2c-adapter i2c-1: unable to read EDID block.
[  249.649072] i915 0000:00:02.0: LVDS-1: no EDID data
[  494.012164]  CIFS VFS: Error connecting to socket. Aborting operation
[  494.012195]  CIFS VFS: cifs_mount failed w/return code = -110
[ 1578.309302] CE: hpet increasing min_delta_ns to 22500 nsec
[ 1651.351688] CE: hpet increasing min_delta_ns to 33750 nsec
[ 1971.520157] CE: hpet increasing min_delta_ns to 50624 nsec
[ 1997.192175] CE: hpet increasing min_delta_ns to 75936 nsec
[ 6656.873774] warning: `VirtualBox' uses 32-bit capabilities (legacy support in use)
[ 6851.717292] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 6851.717317] vboxdrv: Successfully done.
[ 6851.717321] vboxdrv: Found 2 processor cores.
[ 6851.719247] vboxdrv: fAsync=0 offMin=0x840 offMax=0xa17c
[ 6851.719275] Platform driver 'vboxdrv' needs updating - please use dev_pm_ops
[ 6851.720593] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 6851.720617] vboxdrv: Successfully loaded version 3.0.2 (interface 0x000e0000).
[ 8605.500126] usb 3-1: reset full speed USB device using uhci_hcd and address 2
[ 8605.760894] usb 2-2: reset full speed USB device using uhci_hcd and address 2
[19843.681427] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[19865.194920] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[19878.193480] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[19956.203710] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[19996.487560] sr0: CDROM not ready.  Make sure there is a disc in the drive.
[20227.208076] i2c-adapter i2c-1: unable to read EDID block.
[20227.208081] i915 0000:00:02.0: LVDS-1: no EDID data