Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Linux version 2.6.27.9-159.fc10.i686 (mockbuild@x86-3.fedora.phx.redhat.com) (gcc version 4.3.2 20081105 (Red Hat 4.3.2-7) (GCC) ) #1 SMP Tue Dec 16 15:12:04 EST 2008 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000002fe40000 (usable) BIOS-e820: 000000002fe40000 - 000000002fe50000 (ACPI data) BIOS-e820: 000000002fe50000 - 000000002ff00000 (ACPI NVS) DMI 2.3 present. last_pfn = 0x2fe40 max_arch_pfn = 0x100000 x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 kernel direct mapping tables up to 2fe40000 @ 7000-d000 Using x86 segment limits to approximate NX protection RAMDISK: 2fb28000 - 2fe2faa5 ACPI: RSDP 000F7300, 0014 (r0 ACPIAM) ACPI: RSDT 2FE40000, 0030 (r1 INTEL D845GBV2 20030714 MSFT 97) ACPI: FACP 2FE40200, 0081 (r2 INTEL D845GBV2 20030714 MSFT 97) ACPI: DSDT 2FE40370, 3FD7 (r1 INTEL D845GBV2 10A MSFT 100000D) ACPI: FACS 2FE50000, 0040 ACPI: APIC 2FE40300, 0068 (r1 INTEL D845GBV2 20030714 MSFT 97) ACPI: ASF! 2FE44350, 0084 (r16 AMIASF I845GASF 1 MSFT 100000D) 0MB HIGHMEM available. 766MB LOWMEM available. mapped low ram: 0 - 2fe40000 low ram: 00000000 - 2fe40000 bootmap 00009000 - 0000efc8 (9 early reservations) ==> bootmem [0000000000 - 002fe40000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000] #3 [0000400000 - 000097212c] TEXT DATA BSS ==> [0000400000 - 000097212c] #4 [002fb28000 - 002fe2faa5] RAMDISK ==> [002fb28000 - 002fe2faa5] #5 [0000973000 - 0000977000] INIT_PG_TABLE ==> [0000973000 - 0000977000] #6 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000] #7 [0000007000 - 0000009000] PGTABLE ==> [0000007000 - 0000009000] #8 [0000009000 - 000000f000] BOOTMAP ==> [0000009000 - 000000f000] found SMP MP-table at [c00ff780] 000ff780 Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x0002fe40 HighMem 0x0002fe40 -> 0x0002fe40 Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0x00000000 -> 0x0000009f 0: 0x00000100 -> 0x0002fe40 On node 0 totalpages: 196063 free_area_init_node: node 0, pgdat c07f3a80, node_mem_map c1000000 DMA zone: 3967 pages, LIFO batch:0 Normal zone: 190563 pages, LIFO batch:31 Using APIC driver default ACPI: PM-Timer IO Port: 0x408 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled) ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information SMP: Allowing 2 CPUs, 1 hotplug CPUs mapped APIC to ffffb000 (fee00000) mapped IOAPIC to ffffa000 (fec00000) PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 Allocating PCI resources starting at 30000000 (gap: 2ff00000:d0100000) PERCPU: Allocating 41372 bytes of per cpu data NR_CPUS: 32, nr_cpu_ids: 2, nr_node_ids 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 194530 Kernel command line: ro root=UUID=38b19631-670b-4ec8-be1a-a65458d523ae Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 CPU 0 irqstacks, hard=c089f000 soft=c087f000 PID hash table entries: 4096 (order: 12, 16384 bytes) TSC: PIT calibration confirmed by PMTIMER. TSC: using PMTIMER calibration value Detected 1799.792 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 768244k/784640k available (2738k kernel code, 15840k reserved, 1418k data, 412k init, 0k highmem) virtual kernel memory layout: fixmap : 0xffc57000 - 0xfffff000 (3744 kB) pkmap : 0xff400000 - 0xff800000 (4096 kB) vmalloc : 0xf0800000 - 0xff3fe000 ( 235 MB) lowmem : 0xc0000000 - 0xefe40000 ( 766 MB) .init : 0xc0815000 - 0xc087c000 ( 412 kB) .data : 0xc06acb96 - 0xc080f618 (1418 kB) .text : 0xc0400000 - 0xc06acb96 (2738 kB) Checking if this processor honours the WP bit even in supervisor mode...Ok. CPA: page pool initialized 1 of 1 pages preallocated SLUB: Genslabs=12, HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Calibrating delay loop (skipped), value calculated using timer frequency.. 3599.58 BogoMIPS (lpj=1799792) Security Framework initialized SELinux: Initializing. SELinux: Starting in permissive mode Mount-cache hash table entries: 512 Initializing cgroup subsys ns Initializing cgroup subsys cpuacct Initializing cgroup subsys devices CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Hyper-Threading is disabled Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU0: Thermal monitoring enabled Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code ACPI: Core revision 20080609 ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 CPU0: Intel(R) Pentium(R) 4 CPU 1.80GHz stepping 07 Brought up 1 CPUs Total of 1 processors activated (3599.58 BogoMIPS). sizeof(vma)=84 bytes sizeof(page)=32 bytes sizeof(inode)=340 bytes sizeof(dentry)=132 bytes sizeof(ext3inode)=492 bytes sizeof(buffer_head)=56 bytes sizeof(skbuff)=184 bytes sizeof(task_struct)=3268 bytes CPU0 attaching NULL sched-domain. net_namespace: 840 bytes Booting paravirtualized kernel on bare hardware Time: 19:27:30 Date: 01/29/09 NET: Registered protocol family 16 No dock devices found. ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1 PCI: Using configuration type 1 for base access ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S1 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: 0000:00:00.0 reg 10 32bit mmio: [f8000000, fbffffff] PCI: 0000:00:02.0 reg 10 32bit mmio: [f0000000, f7ffffff] PCI: 0000:00:02.0 reg 14 32bit mmio: [ffa80000, ffafffff] PCI: 0000:00:1d.0 reg 20 io port: [e800, e81f] PCI: 0000:00:1d.1 reg 20 io port: [e880, e89f] PCI: 0000:00:1d.2 reg 20 io port: [ec00, ec1f] PCI: 0000:00:1d.7 reg 10 32bit mmio: [ffa7fc00, ffa7ffff] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold pci 0000:00:1d.7: PME# disabled * The chipset may have PM-Timer Bug. Due to workarounds for a bug, * this clock source is slow. If you are sure your timer does not have * this bug, please use "acpi_pm_good" to disable the workaround HPET not enabled in BIOS. You might try hpet=force boot option pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH4 GPIO PCI: 0000:00:1f.1 reg 10 io port: [0, 7] PCI: 0000:00:1f.1 reg 14 io port: [0, 3] PCI: 0000:00:1f.1 reg 18 io port: [0, 7] PCI: 0000:00:1f.1 reg 1c io port: [0, 3] PCI: 0000:00:1f.1 reg 20 io port: [ffa0, ffaf] PCI: 0000:00:1f.1 reg 24 32bit mmio: [0, 3ff] PCI: 0000:00:1f.3 reg 20 io port: [e000, e01f] PCI: 0000:00:1f.5 reg 10 io port: [e400, e4ff] PCI: 0000:00:1f.5 reg 14 io port: [e080, e0bf] PCI: 0000:00:1f.5 reg 18 32bit mmio: [ffa7f800, ffa7f9ff] PCI: 0000:00:1f.5 reg 1c 32bit mmio: [ffa7f400, ffa7f4ff] pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold pci 0000:00:1f.5: PME# disabled PCI: 0000:01:00.0 reg 10 32bit mmio: [ff8fd000, ff8fdfff] pci 0000:01:00.0: supports D1 pci 0000:01:00.0: supports D2 pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot pci 0000:01:00.0: PME# disabled PCI: 0000:01:00.1 reg 10 32bit mmio: [ff8fe000, ff8fefff] pci 0000:01:00.1: supports D1 pci 0000:01:00.1: supports D2 pci 0000:01:00.1: PME# supported from D0 D1 D2 D3hot pci 0000:01:00.1: PME# disabled PCI: 0000:01:00.2 reg 10 32bit mmio: [ff8ffc00, ff8ffcff] pci 0000:01:00.2: supports D1 pci 0000:01:00.2: supports D2 pci 0000:01:00.2: PME# supported from D0 D1 D2 D3hot pci 0000:01:00.2: PME# disabled PCI: 0000:01:01.0 reg 20 io port: [d880, d89f] PCI: 0000:01:01.1 reg 20 io port: [dc00, dc1f] PCI: 0000:01:01.2 reg 10 32bit mmio: [ff8ff800, ff8ff8ff] pci 0000:01:01.2: PME# supported from D0 D3hot pci 0000:01:01.2: PME# disabled PCI: 0000:01:02.0 reg 10 32bit mmio: [ff8e0000, ff8effff] PCI: 0000:01:02.0 reg 14 32bit mmio: [e6af0000, e6afffff] PCI: 0000:01:02.0 reg 18 32bit mmio: [ff8d0000, ff8dffff] PCI: 0000:01:08.0 reg 10 32bit mmio: [ff8fc000, ff8fcfff] PCI: 0000:01:08.0 reg 14 io port: [d800, d83f] pci 0000:01:08.0: supports D1 pci 0000:01:08.0: supports D2 pci 0000:01:08.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:01:08.0: PME# disabled pci 0000:00:1e.0: transparent bridge PCI: bridge 0000:00:1e.0 io port: [d000, dfff] PCI: bridge 0000:00:1e.0 32bit mmio: [ff800000, ff8fffff] PCI: bridge 0000:00:1e.0 32bit mmio pref: [e6a00000, e6afffff] bus 00 -> node 0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) ACPI: Power Resource [URP1] (off) ACPI: Power Resource [FDDP] (off) ACPI: Power Resource [LPTP] (off) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 14 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default tracer: 772 pages allocated for 65536 entries of 48 bytes actual entries 65620 ACPI: RTC can wake from S4 system 00:05: ioport range 0x4d0-0x4d1 has been reserved system 00:0c: ioport range 0x400-0x47f has been reserved system 00:0c: ioport range 0x680-0x6ff has been reserved system 00:0c: ioport range 0x480-0x4bf has been reserved system 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved system 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved system 00:0d: iomem range 0x0-0x9ffff could not be reserved system 00:0d: iomem range 0xc0000-0xdffff could not be reserved system 00:0d: iomem range 0xe0000-0xfffff could not be reserved system 00:0d: iomem range 0x100000-0x2fefffff could not be reserved pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01 pci 0000:00:1e.0: IO window: 0xd000-0xdfff pci 0000:00:1e.0: MEM window: 0xff800000-0xff8fffff pci 0000:00:1e.0: PREFETCH window: 0x000000e6a00000-0x000000e6afffff pci 0000:00:1e.0: setting latency timer to 64 bus: 00 index 0 io port: [0, ffff] bus: 00 index 1 mmio: [0, ffffffffffffffff] bus: 01 index 0 io port: [d000, dfff] bus: 01 index 1 mmio: [ff800000, ff8fffff] bus: 01 index 2 mmio: [e6a00000, e6afffff] bus: 01 index 3 io port: [0, ffff] bus: 01 index 4 mmio: [0, ffffffffffffffff] NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered NET: Registered protocol family 1 checking if image is initramfs... it is Freeing initrd memory: 3102k freed apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) apm: overridden by ACPI. audit: initializing netlink socket (disabled) type=2000 audit(1233257249.521:1): initialized HugeTLB registered 4 MB page size, pre-allocated 0 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) msgmni has been set to 1506 SELinux: Registering netfilter hooks Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) pci 0000:00:02.0: Boot video device Switched to high resolution mode on CPU 0 pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001 pci 0000:01:08.0: Firmware left e100 interrupts enabled; disabling pci_hotplug: PCI Hot Plug PCI Core version: 0.5 acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 ACPI: Power Button (FF) [PWRF] input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1 ACPI: Sleep Button (CM) [SLPB] processor ACPI0007:00: registered as cooling_device0 ACPI: Processor [CPU1] (supports 8 throttling states) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Non-volatile memory driver v1.2 Linux agpgart interface v0.103 agpgart-intel 0000:00:00.0: Intel 830M Chipset agpgart-intel 0000:00:00.0: detected 892K stolen memory agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xf0000000 Serial: 8250/16550 driver4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A brd: module loaded loop: module loaded input: Macintosh mouse button emulation as /devices/virtual/input/input2 Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods ata_piix 0000:00:1f.1: version 2.12 ata_piix 0000:00:1f.1: enabling device (0005 -> 0007) ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 ata_piix 0000:00:1f.1: setting latency timer to 64 scsi0 : ata_piix scsi1 : ata_piix ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14 ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15 ata1.00: ATA-6: ST380011A, 3.06, max UDMA/100 ata1.00: 156301488 sectors, multi 16: LBA48 ata1.01: ATA-7: Maxtor 6Y080P0, YAR41BW0, max UDMA/133 ata1.01: 160086528 sectors, multi 16: LBA ata1.00: configured for UDMA/100 ata1.01: configured for UDMA/100 ata2.01: NODEV after polling detection ata2.00: ATAPI: PLEXTOR DVDR PX-740A, 1.01, max UDMA/33 ata2.00: configured for UDMA/33 scsi 0:0:0:0: Direct-Access ATA ST380011A 3.06 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 > sda4 sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 0:0:1:0: Direct-Access ATA Maxtor 6Y080P0 YAR4 PQ: 0 ANSI: 5 sd 0:0:1:0: [sdb] 160086528 512-byte hardware sectors (81964 MB) sd 0:0:1:0: [sdb] Write Protect is off sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00 sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:1:0: [sdb] 160086528 512-byte hardware sectors (81964 MB) sd 0:0:1:0: [sdb] Write Protect is off sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00 sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 sdb9 > sd 0:0:1:0: [sdb] Attached SCSI disk sd 0:0:1:0: Attached scsi generic sg1 type 0 scsi 1:0:0:0: CD-ROM PLEXTOR DVDR PX-740A 1.01 PQ: 0 ANSI: 5 sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 1:0:0:0: Attached scsi CD-ROM sr0 sr 1:0:0:0: Attached scsi generic sg2 type 5 ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23 ehci_hcd 0000:00:1d.7: setting latency timer to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported ehci_hcd 0000:00:1d.7: irq 23, io mem 0xffa7fc00 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.27.9-159.fc10.i686 ehci_hcd usb usb1: SerialNumber: 0000:00:1d.7 ehci_hcd 0000:01:00.2: PCI INT C -> GSI 23 (level, low) -> IRQ 23 ehci_hcd 0000:01:00.2: EHCI Host Controller ehci_hcd 0000:01:00.2: new USB bus registered, assigned bus number 2 ehci_hcd 0000:01:00.2: irq 23, io mem 0xff8ffc00 ehci_hcd 0000:01:00.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 5 ports detected usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: EHCI Host Controller usb usb2: Manufacturer: Linux 2.6.27.9-159.fc10.i686 ehci_hcd usb usb2: SerialNumber: 0000:01:00.2 ehci_hcd 0000:01:01.2: PCI INT C -> GSI 20 (level, low) -> IRQ 20 ehci_hcd 0000:01:01.2: EHCI Host Controller ehci_hcd 0000:01:01.2: new USB bus registered, assigned bus number 3 ehci_hcd 0000:01:01.2: irq 20, io mem 0xff8ff800 ehci_hcd 0000:01:01.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 4 ports detected usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: EHCI Host Controller usb usb3: Manufacturer: Linux 2.6.27.9-159.fc10.i686 ehci_hcd usb usb3: SerialNumber: 0000:01:01.2 ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ohci_hcd 0000:01:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 ohci_hcd 0000:01:00.0: OHCI Host Controller ohci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 4 ohci_hcd 0000:01:00.0: irq 21, io mem 0xff8fd000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 3 ports detected usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: OHCI Host Controller usb usb4: Manufacturer: Linux 2.6.27.9-159.fc10.i686 ohci_hcd usb usb4: SerialNumber: 0000:01:00.0 ohci_hcd 0000:01:00.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22 ohci_hcd 0000:01:00.1: OHCI Host Controller ohci_hcd 0000:01:00.1: new USB bus registered, assigned bus number 5 ohci_hcd 0000:01:00.1: irq 22, io mem 0xff8fe000 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: OHCI Host Controller usb usb5: Manufacturer: Linux 2.6.27.9-159.fc10.i686 ohci_hcd usb usb5: SerialNumber: 0000:01:00.1 USB Universal Host Controller Interface driver v3.0 uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 uhci_hcd 0000:00:1d.0: setting latency timer to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000e800 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb6: Product: UHCI Host Controller usb usb6: Manufacturer: Linux 2.6.27.9-159.fc10.i686 uhci_hcd usb usb6: SerialNumber: 0000:00:1d.0 uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 uhci_hcd 0000:00:1d.1: setting latency timer to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e880 usb usb7: configuration #1 chosen from 1 choice hub 7-0:1.0: USB hub found hub 7-0:1.0: 2 ports detected usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb7: Product: UHCI Host Controller usb usb7: Manufacturer: Linux 2.6.27.9-159.fc10.i686 uhci_hcd usb usb7: SerialNumber: 0000:00:1d.1 uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 uhci_hcd 0000:00:1d.2: setting latency timer to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ec00 usb usb8: configuration #1 chosen from 1 choice hub 8-0:1.0: USB hub found hub 8-0:1.0: 2 ports detected usb usb8: New USB device found, idVendor=1d6b, idProduct=0001 usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb8: Product: UHCI Host Controller usb usb8: Manufacturer: Linux 2.6.27.9-159.fc10.i686 uhci_hcd usb usb8: SerialNumber: 0000:00:1d.2 uhci_hcd 0000:01:01.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 uhci_hcd 0000:01:01.0: UHCI Host Controller uhci_hcd 0000:01:01.0: new USB bus registered, assigned bus number 9 uhci_hcd 0000:01:01.0: irq 22, io base 0x0000d880 usb usb9: configuration #1 chosen from 1 choice hub 9-0:1.0: USB hub found hub 9-0:1.0: 2 ports detected usb usb9: New USB device found, idVendor=1d6b, idProduct=0001 usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb9: Product: UHCI Host Controller usb usb9: Manufacturer: Linux 2.6.27.9-159.fc10.i686 uhci_hcd usb usb9: SerialNumber: 0000:01:01.0 uhci_hcd 0000:01:01.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 uhci_hcd 0000:01:01.1: UHCI Host Controller uhci_hcd 0000:01:01.1: new USB bus registered, assigned bus number 10 uhci_hcd 0000:01:01.1: irq 21, io base 0x0000dc00 usb usb10: configuration #1 chosen from 1 choice hub 10-0:1.0: USB hub found hub 10-0:1.0: 2 ports detected usb usb10: New USB device found, idVendor=1d6b, idProduct=0001 usb usb10: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb10: Product: UHCI Host Controller usb usb10: Manufacturer: Linux 2.6.27.9-159.fc10.i686 uhci_hcd usb usb10: SerialNumber: 0000:01:01.1 PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one month device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com cpuidle: using governor ladder cpuidle: using governor menu usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver nf_conntrack version 0.5.0 (12288 buckets, 49152 max) CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Plase use nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or sysctl net.netfilter.nf_conntrack_acct=1 to enable it. ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 17 Using IPI No-Shortcut mode registered taskstats version 1 Magic number: 9:91:497 Freeing unused kernel memory: 412k freed Write protecting the kernel text: 2740k Write protecting the kernel read-only data: 1172k input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3 psmouse serio1: ID: 10 00 64<6>input: PS2++ Logitech Mouse as /devices/platform/i8042/serio1/input/input4 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. SELinux: Disabled at runtime. SELinux: Unregistering netfilter hooks type=1404 audit(1233257260.191:2): selinux=0 auid=4294967295 ses=4294967295 udevd version 127 started i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17 intel_rng: Firmware space is locked read-only. If you can't or intel_rng: don't want to disable this in firmware setup, and if intel_rng: you are certain that your system has a functional intel_rng: RNG, try using the 'no_fwh_detect' option. iTCO_vendor_support: vendor-support=0 iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008) iTCO_wdt: Found a ICH4 TCO device (Version=1, TCOBASE=0x0460) iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) parport_pc 00:09: reported by Plug and Play ACPI parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI e100: Copyright(c) 1999-2006 Intel Corporation e100 0000:01:08.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 e100 0000:01:08.0: PME# disabled e100: eth0: e100_probe: addr 0xff8fc000, irq 20, MAC addr 00:0c:f1:a8:ee:4a input: PC Speaker as /devices/platform/pcspkr/input/input5 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 ppdev: user-space parallel port driver Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17 Intel ICH 0000:00:1f.5: setting latency timer to 64 ALSA sound/pci/ac97/ac97_codec.c:2127: AC'97 0 analog subsections not ready intel8x0_measure_ac97_clock: measured 50924 usecs intel8x0: measured clock 216 rejected intel8x0: clocking to 48000 EXT3 FS on sda8, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda9, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda10, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda4, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda11, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sdb3, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sdb5, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Adding 530104k swap on /dev/sda7. Priority:-1 extents:1 across:530104k e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex lm85 0-002e: Device configuration is locked