dmesg [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.24-19-generic (buildd@palmer) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Wed Jun 18 14:43:41 UTC 2008 (Ubuntu 2.6.24-19.34-generic) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009d800 (usable) [ 0.000000] BIOS-e820: 000000000009d800 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved) [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000bf6b0000 (usable) [ 0.000000] BIOS-e820: 00000000bf6b0000 - 00000000bf6cc000 (ACPI data) [ 0.000000] BIOS-e820: 00000000bf6cc000 - 00000000bf700000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000bf700000 - 00000000c0000000 (reserved) [ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) [ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved) [ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved) [ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 0000000140000000 (usable) [ 0.000000] Warning only 4GB will be used. [ 0.000000] Use a HIGHMEM64G enabled kernel. [ 0.000000] 3200MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at 000f69f0 [ 0.000000] Entering add_active_range(0, 0, 1048576) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 1048576 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 1048576 [ 0.000000] On node 0 totalpages: 1048576 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 6400 pages used for memmap [ 0.000000] HighMem zone: 812800 pages, LIFO batch:31 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] DMI present. [ 0.000000] ACPI: RSDP signature @ 0xC00F69C0 checksum 0 [ 0.000000] ACPI: RSDP 000F69C0, 0024 (r2 LENOVO) [ 0.000000] ACPI: XSDT BF6BB3E9, 0094 (r1 LENOVO TP-7K 2170 LTP 0) [ 0.000000] ACPI: FACP BF6BB500, 00F4 (r3 LENOVO TP-7K 2170 LNVO 1) [ 0.000000] ACPI Warning (tbfadt-0442): Optional field "Gpe1Block" has zero address or length: 000000000000102C/0 [20070126] [ 0.000000] ACPI: DSDT BF6BB91D, 102E1 (r1 LENOVO TP-7K 2170 MSFT 3000000) [ 0.000000] ACPI: FACS BF6E4000, 0040 [ 0.000000] ACPI: SSDT BF6BB6B4, 0269 (r1 LENOVO TP-7K 2170 MSFT 3000000) [ 0.000000] ACPI: ECDT BF6CBBFE, 0052 (r1 LENOVO TP-7K 2170 LNVO 1) [ 0.000000] ACPI: TCPA BF6CBC50, 0032 (r2 LENOVO TP-7K 2170 LNVO 1) [ 0.000000] ACPI: APIC BF6CBC82, 0068 (r1 LENOVO TP-7K 2170 LNVO 1) [ 0.000000] ACPI: MCFG BF6CBCEA, 003C (r1 LENOVO TP-7K 2170 LNVO 1) [ 0.000000] ACPI: HPET BF6CBD26, 0038 (r1 LENOVO TP-7K 2170 LNVO 1) [ 0.000000] ACPI: SLIC BF6CBE62, 0176 (r1 LENOVO TP-7K 2170 LTP 0) [ 0.000000] ACPI: BOOT BF6CBFD8, 0028 (r1 LENOVO TP-7K 2170 LTP 1) [ 0.000000] ACPI: SSDT BF6E26D9, 025F (r1 LENOVO TP-7K 2170 INTL 20050513) [ 0.000000] ACPI: SSDT BF6E2938, 00A6 (r1 LENOVO TP-7K 2170 INTL 20050513) [ 0.000000] ACPI: SSDT BF6E29DE, 04F7 (r1 LENOVO TP-7K 2170 INTL 20050513) [ 0.000000] ACPI: SSDT BF6E2ED5, 08BD (r1 LENOVO TP-7K 2170 INTL 20050513) [ 0.000000] ACPI: SSDT BF6E3792, 069C (r1 LENOVO TP-7K 2170 INTL 20050513) [ 0.000000] ACPI: DMI detected: Lenovo ThinkPad R61 [ 0.000000] ACPI: Added _OSI(Linux) [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 6:15 APIC version 20 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) [ 0.000000] Processor #1 6:15 APIC version 20 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at c4000000 (gap: c0000000:30000000) [ 0.000000] swsusp: Registered nosave memory region: 000000000009d000 - 000000000009e000 [ 0.000000] swsusp: Registered nosave memory region: 000000000009e000 - 00000000000a0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d2000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000d2000 - 00000000000d4000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000d4000 - 00000000000e0000 [ 0.000000] swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1040384 [ 0.000000] Kernel command line: root=UUID=9f60086d-6a84-4d5a-b9f7-dc3234172c30 ro quiet splash [ 0.000000] mapped APIC to ffffb000 (fee00000) [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Detected 1995.050 MHz processor. [ 13.118297] Console: colour VGA+ 80x25 [ 13.118300] console [tty0] enabled [ 13.118573] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 13.118829] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 13.280674] Memory: 3089792k/4194304k available (2177k kernel code, 45100k reserved, 1006k data, 368k init, 2218688k highmem) [ 13.280680] virtual kernel memory layout: [ 13.280681] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB) [ 13.280682] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 13.280683] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 13.280683] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 13.280684] .init : 0xc0421000 - 0xc047d000 ( 368 kB) [ 13.280685] .data : 0xc0320434 - 0xc041bdc4 (1006 kB) [ 13.280686] .text : 0xc0100000 - 0xc0320434 (2177 kB) [ 13.280688] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 13.280723] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1 [ 13.280854] hpet clockevent registered [ 13.360816] Calibrating delay using timer specific routine.. 3993.94 BogoMIPS (lpj=7987896) [ 13.360834] Security Framework initialized [ 13.360840] SELinux: Disabled at boot. [ 13.360851] AppArmor: AppArmor initialized [ 13.360854] Failure registering capabilities with primary security module. [ 13.360860] Mount-cache hash table entries: 512 [ 13.360961] Initializing cgroup subsys ns [ 13.360965] Initializing cgroup subsys cpuacct [ 13.360974] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000001 [ 13.360979] monitor/mwait feature present. [ 13.360980] using mwait in idle threads. [ 13.360984] CPU: L1 I cache: 32K, L1 D cache: 32K [ 13.360985] CPU: L2 cache: 4096K [ 13.360987] CPU: Physical Processor ID: 0 [ 13.360988] CPU: Processor Core ID: 0 [ 13.360990] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000001 [ 13.360997] Compat vDSO mapped to ffffe000. [ 13.361008] Checking 'hlt' instruction... OK. [ 13.377121] SMP alternatives: switching to UP code [ 13.378428] Early unpacking initramfs... done [ 13.639911] ACPI: Core revision 20070126 [ 13.639969] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. [ 13.660738] CPU0: Intel(R) Core(TM)2 Duo CPU T7300 @ 2.00GHz stepping 0b [ 13.660751] SMP alternatives: switching to SMP code [ 13.661321] Booting processor 1/1 eip 3000 [ 13.671914] Initializing CPU#1 [ 13.748779] Calibrating delay using timer specific routine.. 3990.00 BogoMIPS (lpj=7980001) [ 13.748785] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 00000001 [ 13.748789] monitor/mwait feature present. [ 13.748791] CPU: L1 I cache: 32K, L1 D cache: 32K [ 13.748793] CPU: L2 cache: 4096K [ 13.748795] CPU: Physical Processor ID: 0 [ 13.748796] CPU: Processor Core ID: 1 [ 13.748797] CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 00000001 [ 13.749319] CPU1: Intel(R) Core(TM)2 Duo CPU T7300 @ 2.00GHz stepping 0b [ 13.749340] Total of 2 processors activated (7983.94 BogoMIPS). [ 13.749520] ENABLING IO-APIC IRQs [ 13.749710] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 13.896612] checking TSC synchronization [CPU#0 -> CPU#1]: [ 13.916606] Measured 363290 cycles TSC warp between CPUs, turning off TSC clock. [ 13.916608] Marking TSC unstable due to: check_tsc_sync_source failed. [ 13.916623] Brought up 2 CPUs [ 13.916645] CPU0 attaching sched-domain: [ 13.916647] domain 0: span 03 [ 13.916649] groups: 01 02 [ 13.916651] CPU1 attaching sched-domain: [ 13.916653] domain 0: span 03 [ 13.916654] groups: 02 01 [ 13.917015] net_namespace: 64 bytes [ 13.917021] Booting paravirtualized kernel on bare hardware [ 13.917410] Time: 10:55:04 Date: 07/06/08 [ 13.917432] NET: Registered protocol family 16 [ 13.917580] EISA bus registered [ 13.917584] ACPI: bus type pci registered [ 13.918094] PCI: PCI BIOS revision 3.00 entry at 0xfddb7, last bus=24 [ 13.918096] PCI: Using configuration type 1 [ 13.918103] Setting up standard PCI resources [ 13.921570] ACPI: EC: EC description table is found, configuring boot EC [ 13.921740] ACPI: EC: non-query interrupt received, switching to interrupt mode [ 13.927412] ACPI: BIOS _OSI(Linux) query honored via DMI [ 14.004107] ACPI: Interpreter enabled [ 14.004110] ACPI: (supports S0 S3 S4 S5) [ 14.004123] ACPI: Using IOAPIC for interrupt routing [ 14.012068] ACPI: EC: GPE = 0x12, I/O: command/status = 0x66, data = 0x62 [ 14.012070] ACPI: EC: driver started in poll mode [ 14.012230] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 14.014265] PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO [ 14.014271] PCI quirk: region 1180-11bf claimed by ICH6 GPIO [ 14.015788] PCI: Transparent bridge - 0000:00:1e.0 [ 14.015945] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 14.016121] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP0._PRT] [ 14.016246] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT] [ 14.016369] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT] [ 14.016491] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT] [ 14.016616] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP4._PRT] [ 14.016743] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] [ 14.019891] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11) [ 14.020102] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11) [ 14.020309] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11) [ 14.020516] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11) [ 14.020722] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11) [ 14.020932] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11) [ 14.021138] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11) [ 14.021345] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11) [ 14.021339] ACPI: EC: non-query interrupt received, switching to interrupt mode [ 14.021614] ACPI: Power Resource [PUBS] (on) [ 14.021667] Linux Plug and Play Support v0.97 (c) Adam Belay [ 14.021692] pnp: PnP ACPI init [ 14.021698] ACPI: bus type pnp registered [ 14.022891] pnpacpi: exceeded the max number of mem resources: 12 [ 14.025472] pnp: PnP ACPI: found 11 devices [ 14.025474] ACPI: ACPI bus type pnp unregistered [ 14.025477] PnPBIOS: Disabled by ACPI PNP [ 14.025834] PCI: Using ACPI for IRQ routing [ 14.025836] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 14.272590] NET: Registered protocol family 8 [ 14.272591] NET: Registered protocol family 20 [ 14.272623] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 14.272626] hpet0: 3 64-bit timers, 14318180 Hz [ 14.273656] AppArmor: AppArmor Filesystem Enabled [ 14.276302] Time: hpet clocksource has been installed. [ 14.276322] Switched to high resolution mode on CPU 0 [ 14.276594] Switched to high resolution mode on CPU 1 [ 14.285478] system 00:00: iomem range 0x0-0x9ffff could not be reserved [ 14.285480] system 00:00: iomem range 0xc0000-0xc3fff could not be reserved [ 14.285483] system 00:00: iomem range 0xc4000-0xc7fff could not be reserved [ 14.285485] system 00:00: iomem range 0xc8000-0xcbfff has been reserved [ 14.285487] system 00:00: iomem range 0xcc000-0xcffff has been reserved [ 14.285489] system 00:00: iomem range 0xd0000-0xd3fff could not be reserved [ 14.285492] system 00:00: iomem range 0x0-0x0 could not be reserved [ 14.285494] system 00:00: iomem range 0x0-0x0 could not be reserved [ 14.285496] system 00:00: iomem range 0x0-0x0 could not be reserved [ 14.285498] system 00:00: iomem range 0xe0000-0xe3fff has been reserved [ 14.285500] system 00:00: iomem range 0xe4000-0xe7fff has been reserved [ 14.285502] system 00:00: iomem range 0xe8000-0xebfff has been reserved [ 14.285508] system 00:02: ioport range 0x164e-0x164f has been reserved [ 14.285510] system 00:02: ioport range 0x1000-0x107f has been reserved [ 14.285512] system 00:02: ioport range 0x1180-0x11bf has been reserved [ 14.285514] system 00:02: ioport range 0x800-0x80f has been reserved [ 14.285516] system 00:02: ioport range 0x15e0-0x15ef has been reserved [ 14.285518] system 00:02: ioport range 0x1600-0x165f could not be reserved [ 14.285521] system 00:02: iomem range 0xf0000000-0xf3ffffff could not be reserved [ 14.285524] system 00:02: iomem range 0xfed1c000-0xfed1ffff could not be reserved [ 14.285526] system 00:02: iomem range 0xfed14000-0xfed17fff could not be reserved [ 14.285528] system 00:02: iomem range 0xfed18000-0xfed18fff could not be reserved [ 14.285531] system 00:02: iomem range 0xfed19000-0xfed19fff could not be reserved [ 14.285533] system 00:02: iomem range 0xfed45000-0xfed4bfff could not be reserved [ 14.315916] PCI: Bridge: 0000:00:1c.0 [ 14.315921] IO window: 2000-2fff [ 14.315933] MEM window: fc000000-fdffffff [ 14.315942] PREFETCH window: f8000000-f80fffff [ 14.315949] PCI: Bridge: 0000:00:1c.1 [ 14.315954] IO window: 3000-3fff [ 14.315966] MEM window: dc000000-df3fffff [ 14.315972] PREFETCH window: dfe00000-dfefffff [ 14.315982] PCI: Bridge: 0000:00:1c.2 [ 14.315987] IO window: 4000-4fff [ 14.315999] MEM window: d8000000-d9ffffff [ 14.316007] PREFETCH window: dfb00000-dfbfffff [ 14.316017] PCI: Bridge: 0000:00:1c.3 [ 14.316022] IO window: 5000-5fff [ 14.316034] MEM window: d4000000-d5ffffff [ 14.316042] PREFETCH window: df800000-df8fffff [ 14.316054] PCI: Bridge: 0000:00:1c.4 [ 14.316059] IO window: 6000-6fff [ 14.316071] MEM window: d0000000-d1ffffff [ 14.316079] PREFETCH window: df500000-df5fffff [ 14.316091] PCI: Bus 22, cardbus bridge: 0000:15:00.0 [ 14.316093] IO window: 00007000-000070ff [ 14.316100] IO window: 00007400-000074ff [ 14.316107] PREFETCH window: f4000000-f7ffffff [ 14.316116] MEM window: c4000000-c7ffffff [ 14.316123] PCI: Bridge: 0000:00:1e.0 [ 14.316128] IO window: 7000-afff [ 14.316140] MEM window: f8300000-fbffffff [ 14.316148] PREFETCH window: f4000000-f7ffffff [ 14.316202] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 20 (level, low) -> IRQ 16 [ 14.316211] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 14.316254] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 21 (level, low) -> IRQ 17 [ 14.316261] PCI: Setting latency timer of device 0000:00:1c.1 to 64 [ 14.316312] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 22 (level, low) -> IRQ 18 [ 14.316319] PCI: Setting latency timer of device 0000:00:1c.2 to 64 [ 14.316365] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 23 (level, low) -> IRQ 19 [ 14.316373] PCI: Setting latency timer of device 0000:00:1c.3 to 64 [ 14.316421] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 20 (level, low) -> IRQ 16 [ 14.316426] PCI: Setting latency timer of device 0000:00:1c.4 to 64 [ 14.316448] PCI: Enabling device 0000:00:1e.0 (0005 -> 0007) [ 14.316461] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 14.316490] ACPI: PCI Interrupt 0000:15:00.0[A] -> GSI 16 (level, low) -> IRQ 20 [ 14.316498] PCI: Setting latency timer of device 0000:15:00.0 to 64 [ 14.316509] NET: Registered protocol family 2 [ 14.353455] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 14.353634] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 14.353981] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 14.354139] TCP: Hash tables configured (established 131072 bind 65536) [ 14.354141] TCP reno registered [ 14.365499] checking if image is initramfs... it is [ 14.928542] Freeing initrd memory: 7310k freed [ 14.928680] Simple Boot Flag at 0x35 set to 0x1 [ 14.929251] audit: initializing netlink socket (disabled) [ 14.929263] audit(1215341704.332:1): initialized [ 14.929307] highmem bounce pool size: 64 pages [ 14.930958] VFS: Disk quotas dquot_6.5.1 [ 14.931021] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 14.931132] io scheduler noop registered [ 14.931134] io scheduler anticipatory registered [ 14.931136] io scheduler deadline registered [ 14.931145] io scheduler cfq registered (default) [ 14.931155] Boot video device is 0000:00:02.0 [ 14.931442] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 14.931570] assign_interrupt_mode Found MSI capability [ 14.931670] Allocate Port Service[0000:00:1c.0:pcie00] [ 14.931698] Allocate Port Service[0000:00:1c.0:pcie02] [ 14.931870] PCI: Setting latency timer of device 0000:00:1c.1 to 64 [ 14.932014] assign_interrupt_mode Found MSI capability [ 14.932118] Allocate Port Service[0000:00:1c.1:pcie00] [ 14.932152] Allocate Port Service[0000:00:1c.1:pcie02] [ 14.932327] PCI: Setting latency timer of device 0000:00:1c.2 to 64 [ 14.932448] assign_interrupt_mode Found MSI capability [ 14.932552] Allocate Port Service[0000:00:1c.2:pcie00] [ 14.932579] Allocate Port Service[0000:00:1c.2:pcie02] [ 14.932749] PCI: Setting latency timer of device 0000:00:1c.3 to 64 [ 14.932874] assign_interrupt_mode Found MSI capability [ 14.932953] Allocate Port Service[0000:00:1c.3:pcie00] [ 14.932981] Allocate Port Service[0000:00:1c.3:pcie02] [ 14.933143] PCI: Setting latency timer of device 0000:00:1c.4 to 64 [ 14.933267] assign_interrupt_mode Found MSI capability [ 14.933364] Allocate Port Service[0000:00:1c.4:pcie00] [ 14.933391] Allocate Port Service[0000:00:1c.4:pcie02] [ 14.933680] isapnp: Scanning for PnP cards... [ 15.291511] isapnp: No Plug & Play device found [ 15.313048] Real Time Clock Driver v1.12ac [ 15.313132] hpet_resources: 0xfed00000 is busy [ 15.313173] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 15.314203] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 15.314257] input: Macintosh mouse button emulation as /devices/virtual/input/input0 [ 15.314340] PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12 [ 15.324921] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 15.324925] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 15.344892] mice: PS/2 mouse device common for all mice [ 15.344985] EISA: Probing bus 0 at eisa.0 [ 15.344994] Cannot allocate resource for EISA slot 1 [ 15.344996] Cannot allocate resource for EISA slot 2 [ 15.344998] Cannot allocate resource for EISA slot 3 [ 15.345000] Cannot allocate resource for EISA slot 4 [ 15.345001] Cannot allocate resource for EISA slot 5 [ 15.345003] Cannot allocate resource for EISA slot 6 [ 15.345004] Cannot allocate resource for EISA slot 7 [ 15.345006] Cannot allocate resource for EISA slot 8 [ 15.345007] EISA: Detected 0 cards. [ 15.345010] cpuidle: using governor ladder [ 15.345011] cpuidle: using governor menu [ 15.345075] NET: Registered protocol family 1 [ 15.345098] Using IPI No-Shortcut mode [ 15.345121] registered taskstats version 1 [ 15.345222] Magic number: 0:406:931 [ 15.345265] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 15.345267] EDD information not available. [ 15.345441] Freeing unused kernel memory: 368k freed [ 15.349347] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 [ 16.519293] fuse init (API version 7.9) [ 16.534954] ACPI: SSDT BF6E1B32, 02C4 (r1 PmRef Cpu0Ist 100 INTL 20050513) [ 16.535227] ACPI: SSDT BF6E1E7B, 085E (r1 PmRef Cpu0Cst 100 INTL 20050513) [ 16.538031] Monitor-Mwait will be used to enter C-1 state [ 16.538034] Monitor-Mwait will be used to enter C-2 state [ 16.538036] Monitor-Mwait will be used to enter C-3 state [ 16.538147] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) [ 16.538151] ACPI: Processor [CPU0] (supports 8 throttling states) [ 16.538351] ACPI: SSDT BF6E1A6A, 00C8 (r1 PmRef Cpu1Ist 100 INTL 20050513) [ 16.538607] ACPI: SSDT BF6E1DF6, 0085 (r1 PmRef Cpu1Cst 100 INTL 20050513) [ 16.541183] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3]) [ 16.541187] ACPI: Processor [CPU1] (supports 8 throttling states) [ 16.543671] ACPI: Thermal Zone [THM0] (35 C) [ 16.545211] ACPI: Thermal Zone [THM1] (35 C) [ 16.800284] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 16.800287] Copyright (c) 1999-2006 Intel Corporation. [ 16.800341] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 16 [ 16.800357] PCI: Setting latency timer of device 0000:00:19.0 to 64 [ 16.827067] usbcore: registered new interface driver usbfs [ 16.827085] usbcore: registered new interface driver hub [ 16.827108] usbcore: registered new device driver usb [ 16.831902] e1000: 0000:00:19.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:1e:37:15:1b:c6 [ 16.832227] USB Universal Host Controller Interface driver v3.0 [ 16.932864] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection [ 16.932899] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 20 (level, low) -> IRQ 16 [ 16.932913] PCI: Setting latency timer of device 0000:00:1a.0 to 64 [ 16.932919] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 16.933113] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 [ 16.933154] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001840 [ 16.933262] usb usb1: configuration #1 chosen from 1 choice [ 16.933281] hub 1-0:1.0: USB hub found [ 16.933285] hub 1-0:1.0: 2 ports detected [ 16.992591] SCSI subsystem initialized [ 17.000111] libata version 3.00 loaded. [ 17.038914] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 17 [ 17.038928] PCI: Setting latency timer of device 0000:00:1a.1 to 64 [ 17.038934] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 17.038953] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2 [ 17.038993] uhci_hcd 0000:00:1a.1: irq 17, io base 0x00001860 [ 17.039086] usb usb2: configuration #1 chosen from 1 choice [ 17.039104] hub 2-0:1.0: USB hub found [ 17.039108] hub 2-0:1.0: 2 ports detected [ 17.140146] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 22 (level, low) -> IRQ 18 [ 17.140164] PCI: Setting latency timer of device 0000:00:1a.7 to 64 [ 17.140169] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 17.140191] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 3 [ 17.144143] PCI: cache line size of 32 is not supported by device 0000:00:1a.7 [ 17.144153] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfe225000 [ 17.159707] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 17.159785] usb usb3: configuration #1 chosen from 1 choice [ 17.159804] hub 3-0:1.0: USB hub found [ 17.159808] hub 3-0:1.0: 4 ports detected [ 17.263772] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 19 (level, low) -> IRQ 21 [ 17.263788] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 17.263794] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 17.263814] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4 [ 17.267752] ehci_hcd 0000:00:1d.7: debug port 1 [ 17.267763] PCI: cache line size of 32 is not supported by device 0000:00:1d.7 [ 17.267772] ehci_hcd 0000:00:1d.7: irq 21, io mem 0xfe225400 [ 17.286446] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 17.286523] usb usb4: configuration #1 chosen from 1 choice [ 17.286544] hub 4-0:1.0: USB hub found [ 17.286548] hub 4-0:1.0: 6 ports detected [ 17.386840] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 20 [ 17.386852] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 17.386858] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 17.386878] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5 [ 17.386918] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00001880 [ 17.387013] usb usb5: configuration #1 chosen from 1 choice [ 17.387032] hub 5-0:1.0: USB hub found [ 17.387035] hub 5-0:1.0: 2 ports detected [ 17.490399] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 22 [ 17.490412] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 17.490417] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 17.490435] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6 [ 17.490468] uhci_hcd 0000:00:1d.1: irq 22, io base 0x000018a0 [ 17.490561] usb usb6: configuration #1 chosen from 1 choice [ 17.490580] hub 6-0:1.0: USB hub found [ 17.490584] hub 6-0:1.0: 2 ports detected [ 17.594325] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 23 [ 17.594337] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 17.594342] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 17.594360] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7 [ 17.594397] uhci_hcd 0000:00:1d.2: irq 23, io base 0x000018c0 [ 17.594490] usb usb7: configuration #1 chosen from 1 choice [ 17.594509] hub 7-0:1.0: USB hub found [ 17.594513] hub 7-0:1.0: 2 ports detected [ 17.698453] ata_piix 0000:00:1f.2: version 2.12 [ 17.698464] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ] [ 17.854323] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 16 (level, low) -> IRQ 20 [ 17.854363] PCI: Setting latency timer of device 0000:00:1f.2 to 64 [ 17.854437] scsi0 : ata_piix [ 17.854564] scsi1 : ata_piix [ 17.855584] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x1c00 irq 14 [ 17.855586] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1c08 irq 15 [ 18.018504] ata1.00: ATA-8: FUJITSU MHW2120BH, 00840015, max UDMA/100 [ 18.018507] ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 18.034679] ata1.00: configured for UDMA/100 [ 18.354231] ata2.00: ATAPI: HL-DT-ST DVDRAM GMA-4082N, EX01, max UDMA/33 [ 18.449742] usb 1-1: new full speed USB device using uhci_hcd and address 2 [ 18.525990] ata2.00: configured for UDMA/33 [ 18.526267] scsi 0:0:0:0: Direct-Access ATA FUJITSU MHW2120B 0084 PQ: 0 ANSI: 5 [ 18.529667] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GMA-4082N EX01 PQ: 0 ANSI: 5 [ 18.537990] Driver 'sd' needs updating - please use bus_type methods [ 18.538036] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB) [ 18.538046] sd 0:0:0:0: [sda] Write Protect is off [ 18.538048] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 18.538061] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 18.538099] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB) [ 18.538108] sd 0:0:0:0: [sda] Write Protect is off [ 18.538110] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 18.538122] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 18.538125] sda: sda1 sda2 sda3 sda4 < sda5<4>Driver 'sr' needs updating - please use bus_type methods [ 18.603806] sda6 > [ 18.603920] sd 0:0:0:0: [sda] Attached SCSI disk [ 18.607980] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 18.607997] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 18.622277] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 18.622280] Uniform CD-ROM driver Revision: 3.20 [ 18.622316] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 18.624511] usb 1-1: configuration #1 chosen from 1 choice [ 18.866663] usb 1-2: new full speed USB device using uhci_hcd and address 3 [ 18.995048] Attempting manual resume [ 18.995051] swsusp: Resume From Partition 8:6 [ 18.995052] PM: Checking swsusp image. [ 18.995348] PM: Resume from disk failed. [ 19.004853] EXT3-fs: INFO: recovery required on readonly filesystem. [ 19.004856] EXT3-fs: write access will be enabled during recovery. [ 19.044292] usb 1-2: configuration #1 chosen from 1 choice [ 19.286411] usb 2-1: new low speed USB device using uhci_hcd and address 2 [ 19.388003] kjournald starting. Commit interval 5 seconds [ 19.387833] EXT3-fs: sda5: orphan cleanup on readonly fs [ 19.387838] ext3_orphan_cleanup: deleting unreferenced inode 400935 [ 19.387854] EXT3-fs: sda5: 1 orphan inode deleted [ 19.387855] EXT3-fs: recovery complete. [ 19.390769] EXT3-fs: mounted filesystem with ordered data mode. [ 19.462777] usb 2-1: configuration #1 chosen from 1 choice [ 21.198393] Clocksource tsc unstable (delta = -393728551 ns) [ 23.821050] input: PC Speaker as /devices/platform/pcspkr/input/input2 [ 24.163535] Linux agpgart interface v0.102 [ 24.194649] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 24.331621] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 24.362359] iTCO_vendor_support: vendor-support=0 [ 24.378612] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007) [ 24.378685] iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060) [ 24.378724] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 24.407558] Non-volatile memory driver v1.2 [ 24.467525] agpgart: Detected an Intel 965GM Chipset. [ 24.469214] agpgart: Detected 7676K stolen memory. [ 24.493285] agpgart: AGP aperture is 256M @ 0xe0000000 [ 24.575364] input: Power Button (FF) as /devices/virtual/input/input3 [ 24.599216] ACPI: Power Button (FF) [PWRF] [ 24.599273] input: Lid Switch as /devices/virtual/input/input4 [ 24.599680] ACPI: Lid Switch [LID] [ 24.599724] input: Sleep Button (CM) as /devices/virtual/input/input5 [ 24.615518] thinkpad_acpi: ThinkPad ACPI Extras v0.17 [ 24.615520] thinkpad_acpi: http://ibm-acpi.sf.net/ [ 24.615522] thinkpad_acpi: ThinkPad BIOS 7KETB7WW (2.17 ), EC 7KHT24WW-1.08 [ 24.615523] thinkpad_acpi: Lenovo ThinkPad R61 [ 24.615954] thinkpad_acpi: radio switch found; radios are enabled [ 24.624387] ACPI: Sleep Button (CM) [SLPB] [ 24.625046] thinkpad_acpi: another device driver is already handling bay events [ 24.625048] thinkpad_acpi: disabling subdriver bay [ 24.626893] thinkpad_acpi: standard ACPI backlight interface available, not loading native one... [ 24.627142] input: ThinkPad Extra Buttons as /devices/virtual/input/input6 [ 24.848275] ACPI: WMI-Acer: Mapper loaded [ 24.981173] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input7 [ 25.032157] ACPI: Video Device [VID] (multi-head: yes rom: no post: no) [ 25.033891] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:06/LNXVIDEO:01/input/input8 [ 25.096119] ACPI: Video Device [VID1] (multi-head: yes rom: no post: no) [ 25.132140] Yenta: CardBus bridge found at 0000:15:00.0 [17aa:20c4] [ 25.260927] Yenta: ISA IRQ mask 0x0cb8, PCI irq 20 [ 25.260934] Socket status: 30000006 [ 25.260936] pcmcia: parent PCI bridge I/O window: 0x7000 - 0xafff [ 25.260939] cs: IO port probe 0x7000-0xafff: clean. [ 25.261832] pcmcia: parent PCI bridge Memory window: 0xf8300000 - 0xfbffffff [ 25.261834] pcmcia: parent PCI bridge Memory window: 0xf4000000 - 0xf7ffffff [ 25.427695] ACPI: Battery Slot [BAT0] (battery absent) [ 25.475308] ACPI: AC Adapter [AC] (on-line) [ 25.551595] Bluetooth: Core ver 2.11 [ 25.551669] NET: Registered protocol family 31 [ 25.551671] Bluetooth: HCI device and connection manager initialized [ 25.551673] Bluetooth: HCI socket layer initialized [ 25.594222] Bluetooth: HCI USB driver ver 2.9 [ 25.596393] usbcore: registered new interface driver hci_usb [ 25.678497] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.0 [ 25.678500] iwl3945: Copyright(c) 2003-2007 Intel Corporation [ 25.678667] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 22 [ 25.678681] PCI: Setting latency timer of device 0000:03:00.0 to 64 [ 25.678700] iwl3945: Detected Intel PRO/Wireless 3945ABG Network Connection [ 25.683038] usbcore: registered new interface driver hiddev [ 25.699080] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.1/usb2/2-1/2-1:1.0/input/input9 [ 25.747787] input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.1-1 [ 25.747802] usbcore: registered new interface driver usbhid [ 25.747806] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 25.971187] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x81a0b1, caps: 0xa04793/0x300000 [ 25.971192] serio: Synaptics pass-through port at isa0060/serio1/input0 [ 26.014375] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input10 [ 26.265606] iwl3945: Tunable channels: 13 802.11bg, 23 802.11a channels [ 26.266173] wmaster0: Selected rate control algorithm 'iwl-3945-rs' [ 26.306770] ACPI: PCI Interrupt 0000:00:1b.0[B] -> GSI 17 (level, low) -> IRQ 22 [ 26.306776] hda_intel: probe_mask set to 0x1 for device 17aa:20ac [ 26.306792] PCI: Setting latency timer of device 0000:00:1b.0 to 64 [ 26.349413] cs: IO port probe 0x100-0x3af: clean. [ 26.351165] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7 [ 26.351925] cs: IO port probe 0x820-0x8ff: clean. [ 26.352519] cs: IO port probe 0xc00-0xcf7: clean. [ 26.353262] cs: IO port probe 0xa00-0xaff: clean. [ 26.459058] loop: module loaded [ 26.486409] lp: driver loaded but no devices found [ 26.582667] Adding 2147000k swap on /dev/sda6. Priority:-1 extents:1 across:2147000k [ 26.707715] EXT3 FS on sda5, internal journal [ 27.678262] kjournald starting. Commit interval 5 seconds [ 27.678824] EXT3 FS on sda3, internal journal [ 27.678829] EXT3-fs: mounted filesystem with ordered data mode. [ 27.683704] kjournald starting. Commit interval 5 seconds [ 27.684318] EXT3 FS on sda1, internal journal [ 27.684323] EXT3-fs: mounted filesystem with ordered data mode. [ 27.705737] IBM TrackPoint firmware: 0x0e, buttons: 3/3 [ 27.792675] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input11 [ 28.032175] ip_tables: (C) 2000-2006 Netfilter Core Team [ 28.553567] ACPI: ACPI Dock Station Driver [ 28.555018] ACPI: \_SB_.PCI0.IDE0.PRIM.MSTR: found ejectable bay [ 28.555024] ACPI: \_SB_.PCI0.IDE0.PRIM.MSTR: Adding notify handler [ 28.555046] ACPI: Bay [\_SB_.PCI0.IDE0.PRIM.MSTR] Added [ 28.555060] ACPI: \_SB_.PCI0.SATA.SCND.MSTR: found ejectable bay [ 28.555065] ACPI: \_SB_.PCI0.SATA.SCND.MSTR: Adding notify handler [ 28.555081] ACPI: Error installing bay notify handler [ 28.555083] ACPI: Bay [\_SB_.PCI0.SATA.SCND.MSTR] Added [ 29.414516] apm: BIOS not found. [ 29.496732] ppdev: user-space parallel port driver [ 29.527970] audit(1215334531.618:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5289 profile="/usr/sbin/cupsd" namespace="default" [ 30.792019] Bluetooth: L2CAP ver 2.9 [ 30.792027] Bluetooth: L2CAP socket layer initialized [ 31.001934] Bluetooth: RFCOMM socket layer initialized [ 31.001955] Bluetooth: RFCOMM TTY layer initialized [ 31.001959] Bluetooth: RFCOMM ver 1.8 [ 33.336861] [drm] Initialized drm 1.1.0 20060810 [ 33.341226] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 20 [ 33.341242] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 33.342043] [drm] Initialized i915 1.6.0 20060119 on minor 0 [ 33.371708] mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining [ 39.726801] NET: Registered protocol family 10 [ 39.727290] lo: Disabled Privacy Extensions [ 39.728159] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 39.729595] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 51.579719] CPU0 attaching NULL sched-domain. [ 51.579726] CPU1 attaching NULL sched-domain. [ 51.592065] CPU0 attaching sched-domain: [ 51.592071] domain 0: span 03 [ 51.592074] groups: 01 02 [ 51.592078] CPU1 attaching sched-domain: [ 51.592081] domain 0: span 03 [ 51.592083] groups: 02 01 [ 52.294491] NET: Registered protocol family 17 [ 53.835348] wlan0: Initial auth_alg=0 [ 53.835356] wlan0: authenticate with AP 00:11:50:0e:3f:fb [ 53.836812] wlan0: RX authentication from 00:11:50:0e:3f:fb (alg=0 transaction=2 status=0) [ 53.836818] wlan0: authenticated [ 53.836822] wlan0: associate with AP 00:11:50:0e:3f:fb [ 53.838404] wlan0: RX AssocResp from 00:11:50:0e:3f:fb (capab=0x411 status=0 aid=3) [ 53.838409] wlan0: associated [ 53.840970] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 62.282136] wlan0: no IPv6 routers present [ 202.383073] gnome-terminal[6550]: segfault at 0000005b eip b783385c esp bffab2c0 error 4